Gas Fireplace Installation Roches Point, Keswick — TSSA-Certified
Gas fireplaces in Roches Point, Keswick keep working when the power does, provided the unit has a millivolt or battery ignition. Worth specifying.
Free instant install estimate + $150 off a booked installation
What will a fireplace install cost in Roches Point, Keswick?
Five questions, real Roches Point, Keswick pricing. You get an installed price band including venting, gas, finishing and permit — before anyone calls you.
Gas is still the right answer for most homes in Roches Point, Keswick: real heat during an outage-prone winter, no wood to store, and instant control. We install direct-vent sealed-combustion units, run the gas line, handle the permit, and hand you a commissioning sheet with the actual gas pressure and CO readings recorded.
Direct-vent done properly
Termination clearances to windows, decks, and property lines in Roches Point, Keswick are code-controlled and frequently ignored by cheap installers. We plan the termination before selecting the unit.
Gas line and pressure
An undersized line starves the appliance and shows as a lazy yellow flame. We size the run to the appliance's BTU rating and verify with a manometer at commissioning.
Safety documentation
Every install leaves with a commissioning sheet: inlet and manifold pressure, spillage test result, CO reading, and the technician's TSSA number.
Fireplace Installation pricing in Roches Point, Keswick
Real 2026 ranges. Your exact number is confirmed in writing before any work starts.
| Service | Typical range | Notes |
|---|---|---|
| Gas insert, existing opening | $4,200 – $6,400 | Supplied and installed |
| Direct-vent through exterior wall | $5,400 – $9,200 | Includes venting and termination |
| Gas line extension from meter | $450 – $1,600 | Distance and access dependent |
| Annual service after install | $179 – $259 | Recommended by every manufacturer |
How the visit works in Roches Point, Keswick
- 1
In-home design visit
We measure the opening, check gas supply and venting routes, and confirm what your home in Roches Point, Keswick can actually accept before quoting anything.
- 2
Written fixed quote
Unit, venting, gas line, electrical, finishing, permit, and disposal — itemised, in writing, before you commit.
- 3
Permits and TSSA compliance
Gas work is performed by TSSA-certified technicians and permitted where the municipality requires it. Paperwork is our job, not yours.
- 4
Installation day
Framing checks, direct-vent termination, sealed gas connection, leak test, and electrical hookup — usually a single day for a standard insert.
- 5
Commissioning and safety test
Manometer gas-pressure reading, spillage test, CO check, and flame calibration recorded on the commissioning sheet.
- 6
Handover and warranty
We show you the controls, register the manufacturer warranty, and leave the commissioning sheet, permit, and photos with you.
What Keswick customers say
4.9 out of 5 from 743 reviews across the GTA. A selection relevant to this service below.
I wanted a bigger unit. They explained why it would overheat the room and recommended a smaller model — and were right.
Liner, gas line, and a sealed insert. The room is genuinely warm now instead of drafty. Permit and inspection handled without me lifting a finger.
Cleaned the burner, checked the venting, and adjusted the flame. Tidy work and fair pricing, and they left the commissioning readings with me.
Old builder-grade unit out, new direct-vent in, and the old one hauled away. Zero mess left behind.
Fireplace Installation FAQs — Roches Point, Keswick
Are your gas technicians certified?
Yes — TSSA-certified gas technicians perform every gas connection in Roches Point, Keswick, and the certification number is on your commissioning sheet.
Does a gas fireplace work in a power cut?
Millivolt and battery-ignition models do. Fan-assisted heat distribution stops, but the burner keeps running.
Do I need a permit in Roches Point, Keswick?
Usually yes for new gas lines and venting penetrations. We apply, schedule the inspection, and leave the documentation with you.
How long does the install take?
One day for a standard insert; two to three for a new build-out with framing and finishing.
How much does it cost to run?
A 25,000 BTU unit running four hours a day costs roughly $30 to $55 a month at current Ontario gas rates.
Can you install in a condo?
Where the building allows a compliant vent termination, yes. We handle the property-management paperwork in Roches Point, Keswick.
Book fireplace installation in Roches Point, Keswick
Free instant install estimate + $150 off a booked installation — 24 hour response guaranteed.
Call (437) 475-2233